Please read the important notes at the end of this section before to try any of these methods. If you can't access the computer when it's on, and the standard backdoor passwords didn't work, you'll have to flash the BIOS via hardware. The numbers which follow are two bytes in hex format. QNote that the first letter is a "O" not the number "0". Once you are in the debug environment enter the following commands: You'd better do it in pure MS-DOS mode, not from a MS-DOS shell window in Windows). You can reset the BIOS to its default values using the MS-DOS tool DEBUG (type DEBUG at the command prompt. However, it might happen you don't have one of those programs when you have access to the computer, so you'd better learn how to do manually what they do. If you have access to the computer when it's turned on, you could try one of those programs that remove the password from the BIOS, by invalidating its memory. The last two passwords in the AWARD BIOS list are in Russian. Also remember that passwords are Case Sensitive. Note that the key associated to "_" in the US keyboard corresponds to "?" in some European keyboards (such as Italian and German ones), so - for example - you should type AWARD?SW when using those keyboards. LKWPETER, lkwpeter, BIOSTAR, biostar, BIOSSTAR, biosstar, ALFAROME, Syxz, Wodj Other passwords you may try (for AMI/AWARD or other BIOSes) The first, less invasive, attempt to bypass a BIOS password is to try on of these standard manufacturer's backdoor passwords:ĪWARD SW, AWARD_SW, Award SW, AWARD PW, _award, awkward, J64, j256, j262, j332, j322, 01322222, 589589, 589721, 595595, 598598, HLT, SER, SKY_FOX, aLLy, aLLY, Condo, CONCAT, TTPTHA, aPAf, HLT, KDD, ZBAAACA, ZAAADA, ZJAAADC, djonet, %øåñòü ïpîáåëîâ%, %äåâÿòü ïpîáåëîâ%ĪMI, A.M.I., AMI SW, AMI_SW, BIOS, PASSWORD, HEWITT RAND, Oder When you turn on the host machine, enter the CMOS setup menu (usually you have to press F2, or DEL, or CTRL+ALT+S during the boot sequence) and go to STANDARD CMOS SETUP, and set the channel to which you have put the hard disk as TYPE=Auto, MODE=AUTO, then SAVE & EXIT SETUP. It works on most versions of the AWARD BIOS. Since the CX50x0 devices support graphic outputs only via DVI-I, this setting is always set to DVI.Restart the computer. This setting indicates the output source for the boot process. The current graphics configuration is shown here. Make sure the system stability is not affected and proceed step-by-step (1 MB, 4 MB, 8 MB) Current Configuration The individual options can be used to try and enhance the performance. This option can be used to adapt the frame buffer. (128 MB, 256 MB) On-Chip Frame Buffer Size This option can be used to set the size of the video memory. Under Win.x and DOS this option should be enabled, otherwise it should be disabled. Under DOS the speed benefits is around 40%. If this option is enabled, the option Video BIOS Shadow should also be activated. Please note that caching involves risks, if the cache contains the code and a program wants to write into the BIOS area. If this option is enabled, the cache memory can take the VIDEO BIOS of the graphics card at the address C0000h to C7FFFh into account. Under Windows 95/98 this option is less relevant. If the function is active the cache memory makes use of the available BIOS-ROM, thereby enhancing the performance, although this applies mainly to DOS and Win3.x. During this process critical parameter information relating to memory type, size, speed, voltage interface and module banks are stored in the EEPROM. By default the options are configured via 'By SPD', by reading the content of the SPD (Serial Presence Detect ) unit. This submenu can be used for setting the optimum timing for options, depending on the memory modules used. ↑ ↓ → ← :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:Helpį5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults DRAM Timing Selectable
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |